Home
Product
About Us
Videos
News
Blog
Contact Us
language
Your Position : Home > News > Successful Cases

15,270 Nanocrystalline Magnetic Cores Shipped to Poland for Smart Metering and EV Charging

Date: Nov 18th, 2026
Read:
Share:

A Polish manufacturer of energy metering and EV charging hardware has received 15,270 nanocrystalline magnetic cores from BIDRAGON. The order left our facility this month as 18 cartons on a single pallet — one consolidated shipment covering both the customer's series production line and a new engineering project.

The delivery includes two very different core sizes. That detail says a lot about where the European energy market is heading.

The Requirement: Accuracy on a Noisier Grid

Poland's grid is being rebuilt from the edge inward. Rooftop PV, heat pumps, home storage and AC/DC chargers all sit behind the meter now, and each of them injects DC components, harmonics and fast transients into the low-voltage side. A core that performs perfectly on a clean sine wave can lose linearity the moment a half-wave rectified load appears — and once phase error drifts, the metering class collapses.

The customer evaluated the two conventional options and rejected both. Silicon steel was stable but too lossy and too sensitive to DC bias at the accuracy level required. Permalloy delivered the permeability, but its cost made the bill of materials unworkable at volume.

Nanocrystalline material sits between the two: saturation flux density around 1.25 T, permeability that can be tuned during annealing, low coercivity, and a cost structure that supports high-volume production.

What Was in the Shipment

Model (ID × OD × HT)

Core type

Quantity

Packing

20×30×10 mm

Nanocrystalline CT core

15,200 pcs

18 cartons

64×40×25 mm

Large-bore nanocrystalline core

70 pcs

18 cartons

Total

—

15,270 pcs

18 cartons / 1 pallet

Two Sizes, Two Different Jobs

The 15,200 pieces of 20×30×10 are the workhorse of the order. This is a nanocrystalline current transformer core with a 20 mm window, sized for the primary conductor of a three-phase DIN-rail meter. Permeability can be adjusted across a wide range during annealing, which lets the designer tune ratio error and phase displacement without changing the mechanical envelope — decisive when one PCB layout has to serve several meter variants for different European utilities.

The 70 pieces of 64×40×25 are a different story. A 40 mm bore takes thick cable or busbar straight through, and at this size the core is normally used for residual current sensing or as a common-mode choke on a charger's AC input stage. Seventy pieces is a trial quantity: enough for engineering validation, type testing and a pilot build, not for series production.

The combination is deliberate. The customer is qualifying the small CT core for meters in volume while validating a large-bore core for a charger platform that has not yet been released. One pallet keeps the qualification timeline and the production schedule in step.

From Ribbon to Finished Core

Both sizes are wound from Fe-based 1K107 nanocrystalline ribbon at roughly 25 µm thickness, then vacuum annealed to develop the nanocrystalline grain structure and, where required, transverse-field annealed to set permeability.

For this batch, the production and QC teams focused on four points:

  • Dimensional tolerance on inner diameter, since the core has to slip over a fixed primary conductor without air gaps.
  • Permeability consistency from piece to piece, so that the customer's compensation algorithm stays valid across the whole reel.
  • DC immunity, verified on samples from each annealing lot rather than on a single reference part.
  • 100% testing before packing — every core, not a statistical sample.

Finished cores are housed in protective cases and handled as precision components. Materials meet RoHS and REACH requirements, and the electrical performance is referenced to the relevant IEC current transformer and metering standards.

Packing for the Transit

Eighteen cartons, one pallet. Inner cartons are cushioned and moisture-protected, the pallet is strapped and stretch-wrapped, and the load is configured for standard EU road freight so it can move from our dock to the customer's incoming inspection area without repalletising.

Consolidating a 15,200-piece series order and a 70-piece engineering batch into one shipment is a small thing operationally. For the customer it means one customs entry, one delivery window and one incoming inspection instead of two of each.

Why This Case Matters Beyond Poland

European metering and charging projects increasingly ask for the same combination: a core that holds accuracy under DC bias, a supplier who can tune permeability to a specific compensation scheme, and capacity that does not break when the order scales from 70 pieces to 15,000.

Poland is one of the fastest-moving EV and smart metering markets in Central Europe, and this shipment reflects the pattern. If you are designing a meter, a residual current device, a charger or an inverter stage and need samples matched to your compensation circuit, talk to our engineering team — we quote against your drawing, your accuracy target and your annual volume.

About BIDRAGON: founded in 2009, BIDRAGON manufactures amorphous and nanocrystalline ribbon, cores and DC-immune CT cores, with roughly eight million cores produced per month and exports to the USA, Spain, Germany, Hungary, Russia, India and other markets.


FAQ

What are nanocrystalline cores used for in smart meters?
They act as the magnetic core of the current transformer inside the meter. High permeability and low coercivity keep ratio error and phase displacement small, so the meter holds its accuracy class even when DC components or harmonics appear on the line.

Can BIDRAGON supply both small CT cores and large-bore cores in one order?
Yes. Cores from 9.5 mm up to 64 mm outer diameter are produced in-house, so a series order for meter CT cores and a trial batch for a charger or residual current design can be consolidated into a single shipment and a single customs entry.

Does the core size have to match an existing meter design?
No. Permeability can be tuned during annealing within a wide range, and case dimensions can be customised, which lets a core be matched to an existing PCB and compensation circuit rather than forcing a redesign.